压气机悬臂静叶流场非定常数值模拟

以现代高压压气机一排悬臂静叶与一排转叶组成的典型级为研究对象,采用非定常数值模拟方法,分析了非定常与定常数值模拟计算得出的级特性线以及峰值效率点气动参数在展向分布的差异,并对悬臂静叶内部流场结构进行了详细分析,结果表明:当悬臂静叶的轮毂设计间隙为2.5%叶高时,非定常计算的综合喘振裕度比定常大5.85%;在峰值效率点工况下,悬臂静叶总压损失和转子效率的非定常影响范围在10%以内,转叶进口相对气流角沿展向分布的影响在0.5°以内。悬臂静叶根部10%叶高以下区域出现了明显的泄漏流动,3.4%叶高压力系数变化最大,轮毂泄漏流起始于20%弦长附近,发展到70%弦长位置时泄漏损失最大,随后逐渐减弱.     

Experimental and Numerical Investigation on Effects of the Steam Ingestion on the Aerodynamic Stability of an Axial Compressor

In order to investigate the influence of steam ingestion on the aerodynamic stability of a two-stage low-speed axial-flow compressor, multiphase flow numerical simulation and experiment were carried out. The total pressure ratio and stall margin of the compressor was decreased under steam ingestion. When the compressor worked at 40% and 53% of the nominal speed, the stall margin decreased, respectively, by 1.5% and 6.3%. The ingested steam reduced the inlet Mach number and increased the thickness of the boundary layer on the suction surface of the blade. The low-speed region around the trailing edge of the blade was increased, and the flow separation region of the boundary layer on the suction surface of the blade was expanded; thus, the compressor was more likely to enter the stall state. The higher the rotational speed, the more significant the negative influence of steam ingestion on the compressor stall margin. The entropy and temperature of air were increased by steam. The heat transfer between steam and air was continuous in compressor passages. The entropy of the air in the later stage was higher than that in the first stage; consequently, the flow loss in the second stage was more serious. Under the combined action of steam ingestion and counter-rotating bulk swirl distortion, the compressor stability margin loss was more obvious. When the rotor speed was 40% and 53% of the nominal speed, the stall margin decreased by 6.3% and 12.64%, respectively.     

压气机超速制造时弹塑性接触的数值模拟

“叶轮超速工艺“是叶轮制造中的一种重要方法.以某柴油机涡轮增压器的压气机为例,采用有限元参数二次规划法结合多重子结构技术分析模拟超速预加载制造时叶轮、轴套与轴之间接触应力的相应分布规律.针对不同的超速转速进行了大量计算,获得了超速转速与接触应力;超速转速与压气机内孔最大残余变形量;超速转速与轴套壁厚之间的关系.结果表明本文所采用的分析方法是可行的,弹塑性接触分析结果可作为叶轮设计及加工工艺的参考.     

航空发动机压气机叶片振动频率与温度的关系

以某型航空发动机压气机第六级叶片为例，研究了温度对叶片振动频率的影响。发现由于温度的升高导致了材料弹性模量的下降，而弹性模量的下降又导致了叶片在发动机一定的转速范围内，除一阶振动外，其余各阶振动的动频均小于静频，因此与通常的工程处理方法不同，研究压气机叶片的动频时，应考虑温度的影响。     

多级轴流压气机叶栅内三维紊流流场的数值模拟

对多级轴流压气机叶栅内三维紊流流场进行数值模拟,采用高精度高分辨率的三阶ENN格式以保证对激波的捕捉和对紊流特征的正确模拟,利用LU-SGS隐式解法提高了计算速度,从而构成了一种既准确又高效的多级跨声速轴流压气机紊流流动数值求解系统。重点研究了动静网格的交接方法及相应的动静交接面处理模型。计算了某带进口导叶的三级轴流压气机,计算结果与实验数据吻合较好。     

采用直、弯静叶压气机时序效应实验研究

本文实验研究了采用直、弯静叶的某重复级低速压气机在不同时序位置时的总性能及横截面流场特性.在不同流量工况下对压气机整体性能及流场进行了详细测量.结果表明,采用正弯静叶的压气机时序效应相对较弱且喘振裕度有所增加;同时,在压比略有减小的前提下(0.1%级别),凭借消耗扭轴功的大幅F降(3%左右),效率在设计工况下最大可提高...     

First experimental research of the bunch compressor at CAEPLI

Magnetic bunch compressor is one of the key technologies on the path to next generation accelerator driven facilities. In this paper we report the design principles and the first experimental research of the bunch compressor developed at Chinese Academy of Engineering Physics (CAEP). The length of the bunch after compressor is found to be about 0.7 ps (rms) and the peak current exceeds 500 A when operated in the optimized condition. The sensitivity of the bunch length on the phase of the acceleration field and magnetic field of the bunch compressor was also measured and analyzed.     

CAES离心压缩机可调扩压器调节规律研究

离心压缩机是压缩空气储能系统中关键设备之一,需具备在较宽流量、压力范围内高负荷高效率运行的能力。作为一种变工况调节技术,可调扩压器可以扩大压缩机工作流量范围,改善气动性能。因此,本文以某压缩空气储能系统用离心压缩机为研究对象,通过数值计算方法研究了可调扩压器调节时压缩机性能变化规律。结果表明采用可调扩压器可以有效拓宽压缩机运行特性,工作流量范围扩大44%,压比范围扩大25%.此后,本文采用Kriging模型获得了压缩机综合性能曲线图和不同储能工况需求下扩压器的调节方案及规律,为压缩空气储能系统离心压缩机变工况主动控制提供了依据。     

涡旋压缩机不对称双涡旋齿型线的构建与模拟

采用双涡旋齿涡旋盘结构能够有效地提高涡旋压缩机的吸气量,然而存在内容积比小、允许开设的排气口面积小的缺点。针对此问题,本文提出一种涡旋压缩机的新型不对称双涡旋齿,利用中线法得到了涡旋齿型线的设计方法,并且建立其几何模型;通过三维数值模拟研究其工作腔内部的气体流场,并与现有的双涡旋齿涡旋压缩机进行对比。结果表明:所提出的涡旋压缩机的新型不对称双涡旋齿能够有效地提高涡旋压缩机的排气量和内容积比,并且增大了排气口的开设面积,使得压缩机具有更好的工作性能。     

吸力面小翼对扩压叶栅间隙泄漏的影响

采用数值模拟方法对利用吸力面小翼方式控制压气机叶栅间隙流动进行研究。结果表明,附加吸力面小翼可以降低叶顶泄漏流速,削弱泄漏涡强度,使得泄漏涡区损失降低。不同宽度吸力面小翼在不同间隙下部可以较好地减少叶尖泄漏,在叶顶间隙为3.3%叶高时,附加相对宽度为0.5的吸力面小翼可使损失降低4.7%。叶顶压差的降低及对泄漏涡结构的改变是吸力面小翼降低泄漏掺混损失的主要原因。